Factory Cheap High Quality Concrete Pig Slat Mold - Mechanical Machine Pump Spares Pump Casing – Special Metal Detail:
The pump casing we offer can meet the followings:
1. Tolerance size of the casting shall conform to ISO8026-3 DCTG 13-RMA 6(RMAG H)-GCTG 7-DS
2. Cracks, burnt, sand and slag inclusions are not allowed. On the unhandled surfaces should not be defects reducing the strength, performance and degrade casting presentation. Allowed correction of welding, in which defective cutting may be performed by the manufacturer’s instruction. Locations of these defects in the casting and the butchering size under welding must be registered and entered in the casting documents. After removal of butchering defects, the surface should be grinded and monitored for completeness remove defects by dye penetration
3. Carry out UT of the castings: the end surfaces along the entire length in the area of the flange connector of the pump housing and cover (zone 1) in the area of the suction flange connector (zone2),in the area of the discharge flange connector (zone3), permitted without correcting defects of the equivalent size to 5mm not more than 3pcs.
4. The conformity checking with the chemical composition of the steels should be carried out from the each melt.
Our main material for cast iron pump cases is similar to followings:
Standard Specifications for Cast Iron |
||
Country |
Standard |
Grade |
China | GB 9439 | HT150,HT200 |
United Kingdom | BS 1452 | Grade150 |
USA | ASTM A 48 | 20B |
ASTM A159 | G1800 | |
Germany | DIN 1691 | GG15, GG20 |
Europe | EN1563 | GJL150,GJL200 |
Japan | JIS G5501 | FC150,FC200 |
International | ISO 185 | 150,200 |
5. The steel mechanical properties: Tensile strength not less 441MPa, elongation Q not less 19%, impact strength not less 392KJ/m2, hardness HB 121-151. The mechanical properties of the steel are necessary to control for each melt. Test results apply to all the castings from this melt, heat-treated in the same mode, record by automatic devices.
Production Process
1. Wooden pattern Production
2. Molding
3. Pouring
4. First cleaning
5. Heat treatment – grinding (inspection)
6. Rough machining (inspection)-finishing machining (inspection)
7. Packing-delivering
Quality assurance
The fabrication route is governed by the provisions of the implemented Quality System ISO 9001: 2000. The standard documentation ensures the full traceability of every process step:
• Manufacturer test certificates according to DIN EN 10.204 § 3.1 including chemical composition, mechanical properties and non-destructive examination;
• Dimensional check supported with a “as-built“ sketch;
• Record of the heat treatment chart
Product detail pictures:
Related Product Guide:
75 Best Gifts for Daughters: The Ultimate List (2018) | Lead Ingot Mold
Thousands of Pot Noodles are served to suspects in police cells as cops deem them “ideal” snack for lags | Copper Foil Manufacturing Facilities
We insist on offering high-quality creation with superior business enterprise concept, honest revenue plus the greatest and fast service. it will bring you not only the high quality solution and huge profit, but essentially the most significant is usually to occupy the endless market for Factory Cheap High Quality Concrete Pig Slat Mold - Mechanical Machine Pump Spares Pump Casing – Special Metal, The product will supply to all over the world, such as: Qatar , Brunei , US , Now, we professionally supplies customers with our main products And our business is not only the "buy" and "sell", but also focus on more. We target to be your loyal supplier and long-term cooperator in China. Now, We hope to be the friends with you.
By Joseph from Yemen - 2016.07.07 13:00
The accounts manager made a detailed introduction about the product, so that we have a comprehensive understanding of the product, and ultimately we decided to cooperate.
By Mag from Puerto Rico - 2016.07.07 13:00